Discussion Forum: Thread 355727 |
|
|
| | Author: | Seajay21 | Posted: | Mar 31, 2024 20:36 | Subject: | Any Advice on Repositioning Stickers? | Viewed: | 86 times | Topic: | General | |
|
| Hello All,
I'm relatively new to Bricklink, so my apologies if this is in the wrong
section of the forum. (If so, I'd appreciate it if someone could point me
to the correct section.)
I recently acquired a 7637 Farm that's mostly complete. Unfortunately, while
there are very few stickers in the set, it seems that most of them are either
misaligned so they overlap two bricks, or placed on the wrong brick.
The most serious cases are two of the cylinder quarters, which have the ends
of their stickers hanging off the edge of the brick by almost a full stud. The
adhesive backing seems to have attracted dust and lint. Fortunately, these are
the only stickers that have lost any stickiness.
The support crane stands have their stickers swapped - so the arrows are pointing
the wrong way. But luckily, these appear to be perfectly intact.
Is there any method that I can use to safely remove/clean/re-stick stickers?
Also, is it necessary or worthwhile to put some sort of sealer (Mod Podge, etc.)
over the top of stickers?
|
|
|
|
| | | | | |
| | | | Author: | Saitobricks.ca | Posted: | Mar 31, 2024 20:59 | Subject: | Re: Any Advice on Repositioning Stickers? | Viewed: | 28 times | Topic: | Help | |
|
| In General, Seajay21 writes:
| Hello All,
I'm relatively new to Bricklink, so my apologies if this is in the wrong
section of the forum. (If so, I'd appreciate it if someone could point me
to the correct section.)
|
Try help
|
I recently acquired a 7637 Farm that's mostly complete. Unfortunately, while
there are very few stickers in the set, it seems that most of them are either
misaligned so they overlap two bricks, or placed on the wrong brick.
|
Unfortunately a common condition for city sets
| The most serious cases are two of the cylinder quarters, which have the ends
of their stickers hanging off the edge of the brick by almost a full stud. The
adhesive backing seems to have attracted dust and lint. Fortunately, these are
the only stickers that have lost any stickiness.
The support crane stands have their stickers swapped - so the arrows are pointing
the wrong way. But luckily, these appear to be perfectly intact.
Is there any method that I can use to safely remove/clean/re-stick stickers?
|
The mouse one may be fixable, but the others are toast.
| Also, is it necessary or worthwhile to put some sort of sealer (Mod Podge, etc.)
over the top of stickers?
|
NO! Please don’t it may seem ok for now, but think of the next guy to get the
set.
I recommend just buying the new stickered parts the set.
Here are the listings you will need.
* | | 2635pb07L Support Crane Stand Double with Black Arrow and '10 MAX' Pattern on Left Side (Sticker) – Set 7637 Parts: Support |
* | | 2635pb07R Support Crane Stand Double with Black Arrow and '10 MAX' Pattern on Right Side (Sticker) – Set 7637 Parts: Support |
|
|
|
| | | | | |
| | | | Author: | stranqe | Posted: | Mar 31, 2024 21:33 | Subject: | Re: Any Advice on Repositioning Stickers? | Viewed: | 23 times | Topic: | General | |
|
| use a heat gun (or at least a hairdryer). Use flat tweezers or small flat nose
pliers to remove the stickers after you've heated them for a minute or so.
I've done it a few times, most the time if the stickers are still "sticky"
this works well.
In General, Seajay21 writes:
| Hello All,
I'm relatively new to Bricklink, so my apologies if this is in the wrong
section of the forum. (If so, I'd appreciate it if someone could point me
to the correct section.)
I recently acquired a 7637 Farm that's mostly complete. Unfortunately, while
there are very few stickers in the set, it seems that most of them are either
misaligned so they overlap two bricks, or placed on the wrong brick.
The most serious cases are two of the cylinder quarters, which have the ends
of their stickers hanging off the edge of the brick by almost a full stud. The
adhesive backing seems to have attracted dust and lint. Fortunately, these are
the only stickers that have lost any stickiness.
The support crane stands have their stickers swapped - so the arrows are pointing
the wrong way. But luckily, these appear to be perfectly intact.
Is there any method that I can use to safely remove/clean/re-stick stickers?
Also, is it necessary or worthwhile to put some sort of sealer (Mod Podge, etc.)
over the top of stickers?
|
|
|
|
| | | | | |
| | | | Author: | Wolflord13 | Posted: | Mar 31, 2024 22:55 | Subject: | Re: Any Advice on Repositioning Stickers? | Viewed: | 33 times | Topic: | General | |
|
| YouTuber named robinhood bricks has an in depth video. Title of the video is
Lego tutorial-Fix,move and repair lego stickers.
|
|
| | | | | | | | | |
| | | | | | Author: | Nubs_Select | Posted: | Apr 1, 2024 00:42 | Subject: | Re: Any Advice on Repositioning Stickers? | Viewed: | 30 times | Topic: | General | |
|
| In General, Wolflord13 writes:
| YouTuber named robinhood bricks has an in depth video. Title of the video is
Lego tutorial-Fix,move and repair lego stickers.
|
Surprised he didn’t name the video “patented tea method”
|
|
|
|
|
|